3D scanning

The dynamic characterization of mechanical components is a crucial issue in industry, especially in the field of rotating machinery. High frequency loads are typical in this field and experimental tools need to fulfill severe specifications to be able to analyze these high-speed phenomena. In this work, an experimental setup, based on a Digital Image Correlation (DIC) technique with a projected speckle pattern, is presented. The proposed approach allows the measurement of vibrational response characterized by a single sinusoidal component having a frequency up to 500 Hz and an amplitude lower than 10 μm.

Keywords: Geometrical inspection , Optiocal touch probe , Reverse Engineering

Mechanical components are often subjected to tolerances and geometrical specification. This paper describes an automatic 3D measurement system based on the integration of a stereo structured light scanner and a tactile probe. The tactile probe is optically tracked by the optical scanner by means of 3D measurements of a prismatic flag, rigidly connected to the probe and equipped with multiple chessboard patterns. Both the stereo vision system and the tactile probe can be easily configured enabling complete reconstructions of components having complex shapes. For instance, structured light scanning can be used to acquire external and visible geometries while tactile probing can be limited to the acquisition of internal and hidden surfaces.

Keywords: Geometrical inspection , Optical touch probe , Reverse Engineering

Clear thermoplastic aligners are nowadays widely used in orthodontics for the correction of malocclusion or teeth misalignment defects. The treatment is virtually designed with a planning software that allows for a definition of a sequence of little movement steps from the initial tooth position to the final desired one. Every single step is transformed into a physical device, the aligner, by the use of a 3D printed model on which a thin foil of plastic material is thermoformed. Manufactured aligners could have inherent limitations such as dimensional instability, low strength, and poor wear resistance. These issues could be associated with material characteristics and/or with the manufacturing processes. The present work aims at the characterization of the manufactured orthodontic devices. Firstly, mechanical properties of different materials have been assessed through a set of tensile tests under different experimental conditions. The tests have the purpose of analyzing the effect that the forming process a d the normal use of the aligner may have on mechanical properties of the material. The manufacturing process could also introduce unexpected limitations in the resulting aligners. This would be a critical element to control in order to establish resulting forces on teeth. Several studies show that resulting forces could be greatly influenced by the aligner thickness. A method to easily measure the actual thickness of the manufactured aligner is proposed. The analysis of a number of real cases shows as the thickness is far to be uniform and could vary strongly along the surface of the tooth.

Keywords: 3D Human Modeling , Clear Aligner , Mechanical Properties Assessment , Optical 3D Scanner , Thermoforming Process , Virtual Design

Orthodontic treatments based on removable thermoplastic aligners are becoming quite common in clinical practice. However, there is no technical literature explaining how the loads are transferred from the thermoformed aligner to the patient dentition. Moreover, the role of auxiliary elements used in combination with the aligner, such as attachments and divots, still needs to be thoroughly explained. This paper is focused on the development of a Finite Element (FE) model to be used in the design process of shape attributes of orthodontic aligners. Geometrical models of a maxillary dental arch, including crown and root shapes, were created by combining optical scanning and Cone Beam Computed Tomography (CBCT). Finite Element Analysis (FEA) was used to compare five different aligner's configurations for the same tooth orthodontic tipping movement (rotation around the tooth's center of resistance). The different scenarios were analyzed by comparing the moment along the mesio-distal direction of the tooth and the resulting moment-to-force ratio (M:F) delivered to the tooth on the plane of interest. Results evidenced the influence of the aligner's configuration on the effectiveness of the planned orthodontic movement.

Keywords: Anatomical modelling , Numerical analysis , Orthodontic aligner , Orthodontic tooth movement

Specifically conceived for applications related to face analytics and tracking, scene segmentation, hand/finger tracking, gaming, augmented reality, and RGB-D cameras are nowadays used even as 3-D scanners. Despite depth cameras' accuracy and precision are not comparable with professional 3-D scanners, they still constitute a promising device for reverse engineering (RE) applications in the close range, due to their low cost. This is particularly true for more recent devices, such as, for instance, the RealSense SR300, which promises to be among the best performing close range depth cameras in the market. Given the potentiality of this new device, and since to date a deep investigation on its performances has not been assessed in scientific literature, the main aim of this paper is to characterize and to provide metrological considerations on the Intel RealSense SR300 depth sensor when this is used as a 3-D scanner. To this end, the device sensor performances are first assessed by applying the existing normative guidelines (i.e. the one published by the Association of German Engineers - Verein Deutscher Ingenieure - VDI/VDE 2634) both to a set of raw captured depth data and to a set acquired with optimized setting of the camera. Then, further assessment of the device performances is carried out by applying some strategies proposed in the literature using optimized sensor setting, to reproduce "real life" conditions for the use as a 3-D scanner. Finally, the performance of the device is critically compared against the performance of latest short-range sensors, thus providing a useful guide, for researchers and practitioners, in an informed choice of the optimal device for their own RE application.

Keywords: depth camera , device characterization , SR300 , structured light , temporal multiplexing , VDI/VDE normative

3D body scanners are nowadays used in a range of applications spanning from health, fashion and fitness to reverse engineering applications for robotics and computer vision. Nowadays very good performances are achievable when using commercial 3D body scanners; however, focusing on relative complex shape of some body details, the results still lack precision and acceptable accuracy. Such critical issue remains unsolved also when dealing with the instantaneous acquisition of the hand-wrist-arm (HWA) anatomy. In this paper, we present a new approach that leverages the emerging 3D depth cameras technologies to design a compact low cost 3D dedicated HWA scanner system capable of delivering almost instantaneous full 3D measurement.

Keywords: 3D body scanner , 3D surface , calibration , depth sensors , hand-wrist-arm anatomy

This paper presents a brief review of recent methods and tools available to designers to perform reverse engineering of CAD models starting from 3D scanned data (mesh/points). Initially, the basic RE framework, shared by the vast majority of techniques, is sketched out. Two main RE strategies are subsequently identified and discussed: automatic approaches and user-guided ones.

Keywords: CAD reconstruction , Constrained Fitting , Reverse Engineering

In the rehabilitation field, the use of additive manufacturing techniques to realize customized orthoses is increasingly widespread. Obtaining a 3D model for the 3D printing phase can be done following different methodologies. We consider the creation of personalized upper limb orthoses, also including fingers, starting from the acquisition of the hand geometry through accurate 3D scanning. However, hand scanning procedure presents differences between healthy subjects and patients affected by pathologies that compromise upper limb functionality. In this work, we present the concept and design of a 3D printed support to assist hand scanning of such patients. The device, realized with FDM additive manufacturing techniques in ABS material, allows palmar acquisitions, and its design and test are motivated by the following needs: (1) immobilizing the hand of patients during the palmar scanning to reduce involuntary movements affecting the scanning quality and (2) keeping hands open and in a correct position, especially to contrast the high degree of hypertonicity of spastic subjects. The resulting device can be used indifferently for the right and the left hand; it is provided in four-dimensional sizes and may be also suitable as a palmar support for the acquisition of the dorsal side of the hand.

Mesoscale geometric modeling of cellular materials is not strictly related only to tomography reconstruction, but it can be applied also in Finite Element Analysis: (a) to better understand load distribution at the interfaces; (b) to develop and calibrate material models; (c) for sensitivity analysis to different loads or shape parameters. This paper aims to examine some of the most applied techniques for geometric modeling of cellular materials at a mesoscale level discussing their advantages and disadvantages for Finite Element Analysis. Among them, two of the most applied techniques, the Voronoi approach and the reverse engineering reconstruction, are here applied to simulate the behavior of aluminum foams under compression. These applications compared to some experimental evidences confirm the capability of mesoscale analysis, highlighting possible enhancement of the geometric modeling techniques.

Keywords: Cellular materials , Finite Element Analysis , Representative Volume Element , Reverse Engineering , Voronoi Diagram

This work presents Reverse Engineering and Computer Aided technologies to improve the inspection of injection moulded electro-mechanical parts. Through a strong integration and automation of these methods, tolerance analysis, acquisition tool-path optimization and data management are performed. The core of the procedure concerns the automation of the data measure originally developed through voxel-based segmentation. This paper discusses the overall framework and its integration made according to Smart Manufacturing requirements. The experimental set-up, now in operative conditions at ABB SACE, is composed of a laser scanner installed on a CMM machine able to measure components with lengths in the range of 5÷250 mm, (b) a tool path optimization procedure and (c) a data management both developed as CAD-based applications.

Keywords: Computer Aided Tolerancing & Inspection , Feature Recognition , Injection Moulding , Path Planning , Product Data Management , Quality Inspection , Reverse Engineering , Segmentation

This work describes a simple, fast, and robust method for identifying, checking and managing the overlapping image keypoints for 3D reconstruction of large objects with numerous geometric singularities and multiple features at different lighting levels. In particular a precision 3D reconstruction of an extensive architecture captured by aerial digital photogrammetry using Unmanned Aerial Vehicles (UAV) is developed. The method was experimentally applied to survey and reconstruct the 'Saraceni' Bridge' at Adrano (Sicily), a valuable example of Roman architecture in brick of historical/cultural interest. The variety of features and different lighting levels required robust self-correlation techniques which would recognise features sometimes even smaller than a pixel in the digital images so as to automatically identify the keypoints necessary for image overlapping and 3D reconstruction. Feature Based Matching (FBM) was used for the low lighting areas like the intrados and the inner arch surfaces, and Area Based Matching (ABM) was used in conjunction to capture the sides and upper surfaces of the bridge. Applying SIFT (Scale Invariant Feature Transform) algorithm during capture helped find distinct features invariant to position, scale and rotation as well as robust for the affinity transformations (changes in scale, rotation, size and position) and lighting variations which are particularly effective in image overlapping. Errors were compared with surveys by total station theodolites, GPS and laser systems. The method can facilitate reconstruction of the most difficult to access parts like the arch intrados and the bridge cavities with high correlation indices.

Keywords: Architectural reconstruction , Area Based Matching , Feature Based Matching , Photogrammetry , SIFT algorithm

This paper describes a methodology for carrying out an accurate mechanical characterization of an amorphous hyperelastic rubber-like material (carbon black filled natural rubber) by a custom-made experimental setup for bulge testing. Generally, during sample testing the slight anisotropy of the internal polymer structures, primarily due to the calendering process is neglected. This methodology is able to evaluate these effects. A hydraulic circuit inflates a thin disk of rubber blocked between two clamping flanges with adjustable flow rate, thus controlling the speed of deformation of the sample. The device has a sliding crossbar, which moves proportionally as the membrane inflates. A stereoscopic technique is able to capture with pixel precision and identify the strain on a silk-screen grid printed on the upper surface of the sample. For each acquisition step, the epipolar geometry of the image pairs is represented in a single absolute reference system integral to the experimental setup. The acquired images are processed using geometrical algorithms and different filters. In this way an extremely precise 3D reconstruction of the sample is created during the bulge test. Slight anisotropic behaviors due to the rubber calendering process have been observed and measured since the first steps of the bulge test, where the strains are minimal and principal strain direction in equibiaxial tension test are determined.

Keywords: Calendered rubber , Equibiaxial Bulge Test , Hyperelastic Materials , Stereoscopic Method , Transverse Isotropy

The shipment of heritage artefacts for restoration or temporary/travelling exhibition has been virtually lacking in customised packaging. Hitherto, packaging has been empirical and intuitive which has unnecessarily put the artefacts at risk. So, this research arises from the need to identify a way of designing and creating packaging for artefacts which takes into account structural criticalities to deal with deteriorating weather, special morphology, constituent materials and manufacturing techniques. The proposed methodology for semi-automatically designing packaging for heritage artefacts includes the integrated and interactive use of Reverse Engineering (RE), Finite Element Analysis (FEA) and Rapid Prototyping (RP). The methodology presented has been applied to create a customised packaging for a small C3rd BC bronze statue of Heracles (Museo Civico “F.L. Belgiorno” di Modica-Italy). This methodology has highlighted how the risk of damage to heritage artefacts can be reduced during shipping. Furthermore, this approach can identify each safety factor and the corresponding risk parameter to stipulate in the insurance policy.

Keywords: Cultural heritage , FEM , Laser scanning , Packaging , Rapid prototyping

Reverse Engineering represents a long-term goal of computer science and engineering; it aims at the reconstruction of digital models from measured data by means of 3D mathematical surfaces and geometrical features representing the geometry of a physical part. In this paper, an overview of constrained fitting optimization methods specifically devised for the reconstruction of mechanical parts is proposed, highlighting the connections between the theoretical problem and some practical solutions. Furthermore, algorithmic procedures are provided in order to underline the main differences between the considered approaches. Critical aspects of constrained fitting and recent trends on Reverse Engineering are finally presented and discussed.

Keywords: CAD reconstruction , Constrained fitting , Optimization algorithms , Reverse engineering

The participation of blind people (BP) in cultural life can be improved by enhancing methodologies and tools for facilitating the 3D reproduction of artworks and, at the same time, to facilitate their exploration. The creation of integrated systems including not only tactile media such as, for instance, sculptures or bas-reliefs but even a set of tools capable of providing the users with an experience cognitively comparable to the one originally envisioned by the artist, may undoubtedly enhance artworks exploration. The present work aims to design a conceptual system to aid BP in the tactile exploration of bas-reliefs. This conceptual system comprises both a hand-tracking system and an audio device, together with a number of methodologies, algorithms and information related to physical design. The designed layout, preliminarily tested to understand its potential and limits, proved to be a promising first attempt in enhancing the BP exploration experience.

Keywords: 3D reconstruction , Blind people , Hand-tracking system , Tactile bas-relief , Tactile exploration

Abstract This paper proposes a review of the methods to detect and represent the human symmetry line. In the last years, the development of 3D scanners has allowed to replace the traditional techniques (marking based methods) with modern methodologies that, starting from a 3D valid discrete geometric model of the back, perform the posture and vertebral column detection based on a complex processing of the acquired data. The purpose of the paper is a critical d iscussion of the state of the art in order to highlight the real potentialit ies and the limitations still present of the most important methodologies proposed for human symmetry line detection.

Keywords: Anatomical landmarks , Back shape analysis , Posture prediction , Rasterstereography , Symmetry line

A feasibility study was performed in order to demonstrate the benefits of designing and manufacturing a customized foot orthosis by means of digital technologies, such as Reverse Engineering (RE), Generative Design (GD) and Additive Manufacturing (AM). The aim of this work was to define the complete design-manufacturing process, starting from the 3D scanning of the human foot anatomy to the direct fabricating of the customized foot orthosis. Moreover, this first methodological study tries to combine a user-friendly semi-automatic modelling approach with the use of low-cost devices for the 3D laser scanning and the 3D printing processes. Finally, the result of this approach, based on digital technologies, was also compared with that achieved by means of conventional manual techniques.

Keywords: Additive manufacturing , Computer aided design , Foot orthosis , Generative design , Reverse engineering

Titanium and its alloys are widely used in cranioplasty because they are biocompatible with excellent mechanical properties and favor the osseointegration with the bone. However, when Titanium alloys have to be worked several problems occurred from a manufacturing point of view: the standard procedure for obtaining Titanium prostheses is represented by the machining processes, which result time and cost consuming. The aim of this research consist to introduce alternative flexible sheet forming processes, i.e. Super Plastic Forming (SPF) and Single Point Incremental Forming (SPIF), for the manufacturing of patient-oriented titanium prostheses. The research activities have already highlighted the potentiality of the investigated forming processes that can be alternatively used taking into account both the damage morphology and the need of urgency operation. In the present work, the way of manufacturing the Ti prostheses by SPF and SPIF is described. A comparative analysis has been performed, thus highlighting the peculiarities of the investigated processes and the prostheses feasibility.

Keywords: Single Point Incremental Forming , Super Plastic Forming , Titanium alloy

During manufacturing, porcelain whiteware changes its shape due to the sintering process. For this reason, leader companies in the field of ceramics apply strict controls on final products in order to reach high quality standards. Typically, three quality parameters are considered: drop of the bottom, bending of the rim and roundness. To date, the assessment of such parameters is still based on visual inspections and manual measurements. In the present paper, authors propose a new quality assessment procedure based on reverse engineering (RE), able to measure the most relevant quality parameters in an effective, reliable and repeatable way.

Keywords: 3D model , 3D reconstruction , 3D scanning , measurement , porcelain , porcelain tableware , quality control , quality parameters , reverse engineering , whiteware

Body scanning presents unique value in delivering the first digital asset of a human body thus resulting a fundamental device for a range of applications dealing with health, fashion and fitness. Despite several body scanners are in the market, recently depth cameras such as Microsoft Kinect® have attracted the 3D community; compared with conventional 3D scanning systems, these sensors are able to capture depth and RGB data at video rate and even if quality and depth resolution are not optimal for this kind of applications, the major benefit comes from the overall acquisition speed and from the IR pattern that allows poor lighting conditions optimal acquisition. When dealing with non-rigid bodies, unfortunately, the use of a single depth camera may lead to inconsistent results mainly caused by wrong surfaces registration. With the aim of improving existing systems based on low-resolution depth cameras, the present paper describes a novel scanning system for capturing 3D full human body models by using multiple Kinect® devices in a compact setup. The system consists of an instantaneous scanning system using eight depth cameras, appropriately arranged in a compact wireframe. To validate the effectiveness of the proposed architecture, a comparison of the obtained 3D body model with the one obtained using a professional Konica Minolta Range Seven 3D scanner is also presented and possible drawbacks are hinted at.

Keywords: 3D modelling , Body scanning , Custom Avatar , Depth Camera , Model Fitting